FLASHFORGE

FLASHFORGE

フィラメント物性表

※2023年02月02日現在

名称
PLA
MODERA:PLA
PLA Galaxy
PLAシルク
PLA木質
PLA Luminous
Green (蓄光)
ABS
ASA
PETG
PBAT
PA
PC
PLA-CF
PETG-CF
PVA
HIPS
プリント温度190~220℃200~230℃200~230℃200~230℃180~220℃190~220℃220~240℃240~260℃220~240℃190~230℃220~260℃240~260℃190~220℃230~250℃190~220℃220~240℃
プリント速度60~90mm/s60~90mm/s60~90mm/s40~60mm/s60~90mm/s60~90mm/s60~90mm/s40~60mm/s60~90mm/s30~60mm/s60~90mm/s60~90mm/s60~90mm/s60~90mm/s60~90mm/s60~90mm/s
お勧め積層0.1~0.2mm0.1~0.2mm0.1~0.2mm0.1~0.2mm0.2mm0.1~0.2mm0.1~0.2mm0.1~0.2mm0.1~0.2mm0.2mm0.1~0.2mm0.1~0.2mm0.1~0.2mm0.1~0.2mm0.2mm0.1~0.2mm
プラットフォーム加熱加熱不要加熱不要加熱不要加熱不要加熱不要加熱不要80~110℃(<100℃,
need Porous plate
100~110℃80~100℃加熱不要80~110℃100~120℃加熱不要70~90℃加熱不要80~110℃(<100℃,
need Porous plate)
ラフト推奨推奨推奨推奨必要推奨必要推奨推奨非推奨必要必要推奨推奨推奨必要
密度1.25±0.05g/cm31.25±0.05g/cm31.25±0.05g/cm31.25±0.05g/cm31.20±0.05g/cm31.25±0.05g/cm31.04±0.2g/cm31.09±0.01g/cm31.27±0.05g/cm31.25±0.05g/cm31.01±0.05g/cm3 1.20±0.05g/cm31.28±0.05g/cm31.28±0.05g/cm31.25±0.05g/cm31.04±0.2g/cm3
メルトフローレート5~7g/10min5~10g/10min5~10g/10min3~5g/10min5~7g/10min5~7g/10min2~4g/10min3~4g/10min5~7g/10min 3~6g/10min5~7g/10min19~21g/10min(300℃,1.2Kg) 5~15g/10min5~15g/10min2~4g/10min2~5g/10min
吸水率(飽和,23℃)0.50%0.50%0.50%0.50%0.50%0.50%1%1.00%0.30%0.50%3.20%0.50%0.50%0.50%——1%
引張強さ≥60MPa≥60MPa≥60MPa≥60MPa≥40MPa≥60MPa≥43MPa≥45Mpa≥52MPa≥35MPa≥55MPa≥50MPa≥56MPa≥68MPa≥10MPa≥30MPa
曲げ強さ≥60MPa≥60MPa≥60MPa≥70MPa≥40MPa≥60MPa≥70MPa≥65Mpa≥88MPa≥35MPa≥58MPa≥89MPa≥98MPa≥15MPa≥60MPa
曲げ弾性率≥2500MPa≥2500MPa≥2500MPa≥2500MPa——≥2500MPa≥2300MPa≥2200MPa≥2200MPa——≥1500MPa≥2200MPa≥2500MPa≥2700MPa≥190MPa≥1800MPa
ノッチ衝擊強さ(IZOD,23℃) ≥16J/m (ASTM D256)≥16J/m (ASTM D256)≥16J/m (ASTM D256)≥16J/m (ASTM D256)≥5J/m (ASTM D256)≥16J/m (ASTM D256)≥108J/m (ASTM D256)
≥19KJ/m2 (ISO179)
≥14KJ/m2 (ISO179)————≥16KJ/m2 (ISO179)≥700J/m (ASTM D256)≥30J/m(ASTM D25)——≥16J/m (ASTM D256)≥100J/m (ASTM D256)
破断伸び率≥3.0%≥3.0%≥3.0%≥10%≥2.0%≥3.0%≥30.0%——≥150.0%≥350.0%≥200.0%≥50.0%≥2%≥50%≥11.0%≥50.0%
熱変形温度≥53℃≥53℃≥53℃≥55℃≥50℃≥53℃≥88℃≥80℃≥70℃≥90℃≥85℃≥125℃≥55℃≥70℃≥55℃≥90℃
直径1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm1.75mm
公差±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.05mm±0.08mm±0.05mm
円度≤0.05mm≤0.05mm≤0.05mm≤0.05mm≤0.05mm≤0.05mm≤0.05mm≤0.05mm≤0.05mm ≤0.05mm≤0.05mm ≤0.08mm ≤0.05mm≤0.05mm≤0.08mm≤0.05mm
TOP